/*

  This example connects to a WEP-encrypted WiFi network.
  Then it prints the MAC address of the WiFi 101 Shield,
  the IP address obtained, and other network details.

  If you use 40-bit WEP, you need a key that is 10 characters long,
  and the characters must be hexadecimal (0-9 or A-F).
  e.g. for 40-bit, ABBADEAF01 will work, but ABBADEAF won't work
  (too short) and ABBAISDEAF won't work (I and S are not
  hexadecimal characters).

  For 128-bit, you need a string that is 26 characters long.
  D0D0DEADF00DABBADEAFBEADED will work because it's 26 characters,
  all in the 0-9, A-F range.

  Circuit:
   WiFi 101 Shield attached

  created 13 July 2010
  by dlf (Metodo2 srl)
  modified 31 May 2012
  by Tom Igoe
*/
#include <SPI.h>
#include <WiFi101_Generic.h>      // https://github.com/khoih-prog/WiFi101_Generic

#include "arduino_secrets.h"
///////please enter your sensitive data in the Secret tab/arduino_secrets.h
char ssid[] = SECRET_SSID;        // your network SSID (name)
char key[] = SECRET_PASS;    // your network password (use for WPA, or use as key for WEP)
int keyIndex = 0;                                // your network key Index number
int status = WL_IDLE_STATUS;                     // the WiFi radio's status

void setup()
{
  //Initialize serial and wait for port to open:
  Serial.begin(115200);

  while (!Serial && millis() < 5000);

  delay(500);

  // check for the presence of the shield:
  if (WiFi.status() == WL_NO_SHIELD)
  {
    Serial.println("WiFi 101 Shield not present");

    // don't continue:
    while (true);
  }

  // attempt to connect to WiFi network:
  while ( status != WL_CONNECTED)
  {
    Serial.print("Attempting to connect to WEP network, SSID: ");
    Serial.println(ssid);
    status = WiFi.begin(ssid, keyIndex, key);

    // wait 10 seconds for connection:
    delay(10000);
  }

  // once you are connected :
  Serial.print("You're connected to the network");
  printCurrentNet();
  printWiFiData();
}

void loop()
{
  // check the network connection once every 10 seconds:
  delay(10000);
  printCurrentNet();
}

void printWiFiData()
{
  // print your WiFi 101 Shield's IP address:
  IPAddress ip = WiFi.localIP();
  Serial.print("IP Address: ");
  Serial.println(ip);
  Serial.println(ip);

  // print your MAC address:
  byte mac[6];
  WiFi.macAddress(mac);
  Serial.print("MAC address: ");
  printMacAddress(mac);
}

void printCurrentNet()
{
  // print the SSID of the network you're attached to:
  Serial.print("SSID: ");
  Serial.println(WiFi.SSID());

  // print the MAC address of the router you're attached to:
  byte bssid[6];
  WiFi.BSSID(bssid);
  Serial.print("BSSID: ");
  printMacAddress(bssid);

  // print the received signal strength:
  long rssi = WiFi.RSSI();
  Serial.print("signal strength (RSSI):");
  Serial.println(rssi);

  // print the encryption type:
  byte encryption = WiFi.encryptionType();
  Serial.print("Encryption Type:");
  Serial.println(encryption, HEX);
  Serial.println();
}

void printMacAddress(byte mac[])
{
  for (int i = 5; i >= 0; i--)
  {
    if (mac[i] < 16)
    {
      Serial.print("0");
    }

    Serial.print(mac[i], HEX);

    if (i > 0)
    {
      Serial.print(":");
    }
  }

  Serial.println();
}